Online Guide and Manuals

Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturers specifications given in owner's manual.

Caster angle is part of front axle design and is not adjustable. If not within specifications, inspect front suspension for wear or damage and replace or repair components as necessary.

Type 1 and 2 (Front) - Camber is adjusted by an eccentric bushing. Loosen nut on upper torsion arm, then rotate eccentric bushing until specified camber angle is obtained. NOTE - Basic setting is with eccentric notch facing in forward position. Adjustment must be made within 90 degrees either direction.

Dasher (Front) - If adjustment is necessary, loosen nuts at attaching ball joint to track control arm. To adjust, insert suitable adjusting tool (40-200) in adjusting holes in control arm and pry ball joint sideways until camber is set to specifications. NOTE - Difference in camber between wheels should not vary more than 1 degrees. Tighten attaching nuts and recheck camber.

NOTE - On dasher models, insert tool from on right side and from rear on left side.

Rabbit and Scirocco (Front) - If adjustment is necessary, loosen nuts of suspension strut-to-wheel bearing housing mounting bolts. Turn eccentric bolt (upper mounting bolt) until specified camber angle is obtained. Tighten mounting bolt nuts and recheck camber angle.

Type 1 (Rear) - Camber angle is dependent on torsion bar adjustment. If camber angle is not within specifications, see Torsion Bar Adjustment.

Type 2 (Rear) - If minor adjustment is necessary, loosen bolts attaching bearing housing to spring plate and diagonal arm. Adjust by changing position of bearing housing in elongated holes in spring plate. Tighten bolts and recheck camber. NOTE - Range that this procedure will cover is very small.

Dasher, Rabbit and Scirocco (Rear) - Rear camber is not adjustable. If camber angle is not to specifications, inspect rear suspension for wear or damage and repair or replace components as necessary.

Type 1 ( Front) - Working on inner end of tie rod, bend up lockplate. Loosen lock nut and clamp bolts from tie rods. Top tapered rings from inn er end of right side tie rod. Rotate tops of tie rods. Forward rotation increases toe-in; rearward rotation decreases toe-in. When specified to is achieved, placte tie rods so ball joints are not angled. Tighten clamp bolts and lock nuts. If steering wheel is centered after making adjustment, use Fig. 1 to recenter steering wheel. NOTE - Centering steering wheel will not alter toe-in

Fig. 1 Direction of Tie Rod Rotation to Align Steering Wheel (Type 1 Only)

Type2 (Front) - 1) Right side tie rod adjust front wheel toe. Press drag link off steering drop arm. Place left side wheel in straight-ahead position. Adjust right side tie rod until specified to is obtained.
2) Place steering gear so protrusion on dust cap is properly aligned. Attach drag link to drop arm. Drag link must enter mounting with no tension against it. Readjust drag link if necessary.

Dasher, Rabbit, Scirocco (Front) - Place front wheels in straight-ahead position. Loosen lock nut on adjustable tie rod end (left side, Dasher; right side, Rabbit and Scirocco). Hold axle boot to avoid twisting. Adjust right side tie rod until specified toe-in.

Type 1 (Rear) - If adjustment is necessary, remove nuts securing spring plate but do not remove bolts. To adjust, move diagonal arm forward or backward in slotted spring plate mounting holes.until toe-in is set to specifications. Install spring plate attaching nuts and recheck toe-in.

Type 2 (Rear) - If adjustment is necessary, loosen bolts attaching bearing housing to spring plate and diagonal arm. Change position of bearing housing in elongated holes on spring plate. Tighten bolts and recheck toe-in.

All Other Models (Rear) - Toe-in is not adjustable. If toe-in is not within specifications, inspect rear suspension for wear or damage and repair or replace components as necessary.

Type 1 - Using a suitable protractor, find deviation of vehicle from horizontal plane and note reading which will be used in setting angle of spring plate. Install spring plate on torsion bar and measure position with protractor. If not within specifications, adjust by moving torsion bar, one spline at a time, forward or backward until correct position is obtained.

Type 2 - Using a suitable protractor, check horizontal position of vehicle on one frame side member. Reading should be noted; it will be used in setting spring plate angle. Insert inner end of torsion bar in center anchor and pres spring plate on outer end of torsion bar. Adjust protractor on unloaded spring plate until bubble is in center position.  Adjust torsion bar one spline forward or rearward until correct specifications are obtained.